We Control The Temperature
This is a cyclic operating temperature sensitive device, which is intended to control the temperature between two particular values under normal operating conditions, automatically switching on or off the electrical circuit. This thermostat can be built to either open or close its electrical contacts as the temperature increases. Once the temperature of the bimetal disc has returned to the specified reset temperature, the contacts will automatically return to their original state. Besides its variety of standard configurations the thermostat can also be customized to the specific technical needs of the customer, assuring maximum design flexibility and usage in broad range of temperature control applications for consumer, industrial and commercial products. Contact Type: Normally Closed; Normally Open T K24 Operating Temperature Range (-45 C to +200 C)
Parameter Parameter Parameter Value Value Value ~ 2 5 0 ~ 2 5 0 ~ 2 5 0 16 16 16 10 30 000 3 50 50 50 1500 1500 1500 3 3 30 000 30 000 100 000 10 to 175 100 000 175 to 200 100 000 - 45 to 10 10 10 Rated voltage, V, not more Rated voltage, V, not more Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,6, not more Rated current, A, at power coeff. 0,6, not more Rated current, A, at power coeff. 0,6, not more Number of automatic cycles, at rated current 10 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 10 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 10 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Electric strength of insulation, V, not less than Electric strength of insulation, V, not less than Electric strength of insulation, V, not less than Heating speed, K/min Heating speed, K/min Heating speed, K/min minimum-0,1; maximum-1,0 minimum-0,1; maximum-1,0 minimum-0,1; maximum-1,0 Degrees of protection provided by enclosure IP4X; IP64 IP4X; IP64 IP64 Degrees of protection provided by enclosure Degrees of protection provided by enclosure 0,005; 0,01; 0,05 0,05 0,05* Contact operating time, ms, not more Contact operating time, ms, not more Contact operating time, ms, not more Tolerance of operating temperature, %, but not less than °C Tolerance of operating temperature, % Tolerance of operating temperature, °C o Reset temperature, lower than operating temperature, C, on o Reset temperature, lower than operating temperature, C, on o Reset temperature, lower than operating temperature, C, on *May differ depending on the wire type and length о Operating temperature, С о Operating temperature, С о Operating temperature, С _ BASIC TECHNICAL DATA FOR TK24 (175 C 200 C) BASIC TECHNICAL DATA FOR TK24 (-45 C - +10 C) _ BASIC TECHNICAL DATA FOR TK24 (10 C 175 C)
25 14.5 4.8 0.8 14.5 11.7 3.2 9.9 0.5 14.5 4.5 3.2 4 4 0.5 26.3 3 14.5 5 0.5 3 14.5 5 5 0.5 30 1.6 14.5 6.3 7.5 0.8 35 1.6 14.5 6.3 0.8 14.5 14 0.8 6.3 10.7 T 03 T 05 T 07 T 09 T 11 T 13 T 04 T 02 T 01 T 06 T 08 T 10 T 12 T 14 14.5 8.5 The only option for TK24 (-45-+10) Wire standard length: 150 mm 14.5 14 0.8 9 31 1.6 14.5 0.8 4.8 4.8 4.8 23 14.5 0.8 2.1 Table 1.1 (TERMINALS) 14.5 Wire information to be specified on the order form (type; cross-section; lengths; stripping) Soldering balls 14.5 8.5 0.5 3 1.5 2 2.7
MG 00 MG 02 MG 04 MG 06 MG 08 MG 01 MG 03 MG 05 MG 07 NO MOUNTING CAP-FLANGE SCREW CAP HEXAHEDRAL 16 ROTATION OR FIXED CLIP ROTATION CLIP TUBE MOUNTING SCREW CAP HEXAHEDRAL 17 Screw parameters (MX, L) to be specified on the order form Screw parameters (MX, L) to be specified on the order form Screw parameters (MX, L) to be specified on the order form Table 1.2 (MOUNTING) 14.5 15.8 0.5 23.8 18.2 16.5 0.1 0.2 3.8 30.4 0.2 14.5 23.8±0.1 20.4 5 15.8 30.4 14.5 35.5 0.1 3.8 42.25 0.2 14.5 0.5 14.5 13 15.8 0.4 25.2 8 4.02 1.9 3.8 18.2 4 16 MX 17 L 16 MX L MX L 14.5 14.5 23 14.5 Tube diameter: 14-20 mm 3.8
B1C B2P B2C B3C B1P Only with lead wires Protection degree IP64 Only with lead wires Protection degree IP64 Only with cables Protection degree IP64 Only with lead wires and screw caps Protection degree IP64 Only with lead wires and screw caps Protection degree IP64 PLASTIC BODY WITH GROUNDING PLASTIC BODY PLASTIC BODY PLASTIC BODY SILICONE CASING Table 1.3 (BODY and/or CASE) CERAMIC BODY CERAMIC BODY CERAMIC BODY CERAMIC BODY 14.5 10.2 14.5 10.2 14.5 7.2 14.5 7.2 B4P B4C B5P B6S B3S STEEL CASING 18 12 18 15 20 15 11.5 MG 09 MG 10 SCREW CAP HEXAHEDRAL 19 Table 1.2 (MOUNTING) 4.8 0.5 20 20 40 10 8 3.7 L 19 3 MX 14.5 14 5 10.7 12.3 6.2 35 20 15 Screw parameters (MX, L) to be specified on the order form 19.5
B1C B2P B2C B1P Table 1.4 (CONTACT TYPE AND CONTACT TRANSIENT RESISTANCE VALUE) Normally closed (NC) 1 2 3 4 5 6 Normally closed (NC) Normally closed (NC) Normally open (NO) Normally open (NO) Normally open (NO) CONTACT TRANSIENT RESISTANCE, mOhm CONTACT TYPE CODE T K24 1 1 2 3 4 5 6 7 4 2 5 3 6 7 MGX** T X* BXX X *** *** PART ORDERING SYSTEM Thermostat model Mounting version (select from Table 1.2) Terminals version (select from Table 1.1) Body version (select from Table 1.3) + Operating temperature value in C and tolerance in - %*** + Reset temperature value in C and tolerance in - %*** Contact type and contact transient resistance value (select from Table 1.4) *For wire terminals, lead wire parameters must be specified when placing an order: insulation type, cross-section area; ends type; lenght; etc. **For screw cap mountings, screw parameters must be specified when placing an order. ***Tolerance in % or C, whichever numerical value is bigger.
Contact Type: Normally Closed T K24HT Operating Temperature Range (+200 C to+425 C) This is a cyclic operating temperature sensitive device, which is intended to control the temperature between two particular values under normal operating conditions, automatically switching off the electrical circuit. This thermostat is designed to operate in higher temperatures. This thermostat is available only with electrical contacts that open as the temperature increases. Once the temperature of the bimetal disc has returned to the specified reset temperature, the contacts will automatically return to their original state. Besides its variety of standard configurations the thermostat can also be customized to the specific technical needs of the customer, assuring maximum design flexibility and usage in broad range of temperature control applications for consumer, industrial and commercial applications.
Parameter Value ~ 2 5 0 6,3 10 10 000 50 1500 3 200 to 425 Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,6, not more Number of automatic cycles, at rated current 10 А and power coeff. 0,95, not less than Electric strength of insulation, V, not less than Heating speed, K/min minimum-0,1; maximum-1,0 Degrees of protection provided by enclosure IP4X 0,05 Contact operating time, ms, not more Tolerance of operating temperature, % o Reset temperature, lower than operating temperature, C, on о Operating temperature, С BASIC TECHNICAL DATA 25 14.5 4.8 0.8 14.5 11.7 3.2 9.9 0.5 14.5 4.5 3.2 4 4 0.5 30 1.6 14.5 6.3 7.5 0.8 35 1.6 14.5 6.3 0.8 14.5 14 0.8 6.3 10.7 T 03 T 07 T 10 T 02 T 01 T 06 T 08 T 11 Table 1.1 (TERMINALS) 31 1.6 14.5 0.8 4.8 4.8 23 14.5 0.8
B1C Table 1.3 (BODY and/or CASE) CERAMIC BODY B2C B3C 14.5 10.2 14.5 7.2 T K24HT 1 1 2 3 4 5 6 4 2 3 5 6 MGX* T X BXX PART ORDERING SYSTEM Thermostat model Mounting version (select from Table 1.2) Terminals version (select from Table 1.1) Body version (select from Table 1.3) + Operating temperature value in C and tolerance in - % + Reset temperature value in C and tolerance in - % *For screw cap mountings, screw parameters must be specified when placing an order. + + TK24HT - T01 - MG04 - B2C - 350 6% - 200 10% - - MG 00 MG 02 MG 04 MG 06 MG 08 MG 01 MG 03 NO MOUNTING CAP-FLANGE CLIP WITH ONE FIXING HOLE SCREW CAP ROUND SCREW CAP HEXAHEDRAL 16 ROTATION OR FIXED CLIP ROTATION CLIP Table 1.2 (MOUNTING) 14.5 15.8 0.5 23.8 18.2 0.1 0.2 3.8 30.4 0.2 14.5 23.8±0.1 20.4 5 15.8 30.4 14.5 35.5 0.1 3.8 42.25 0.2 14.5 14.5 13 15.8 0.4 25.2 8 4.02 3.8 18.2 4 14.5 16 MX L 16 MX L MG 07 SCREW CAP HEXAHEDRAL 17 Screw parameters (MX, L) to be specified on the order form Screw parameters (MX, L) to be specified on the order form Screw parameters (MX, L) to be specified on the order form 14.5 17 MX L 3.8 CERAMIC BODY CERAMIC BODY 14.5 14 5 10.7 12.3 6.2
Contact Type: Normally Closed T K32 Operating Temperature Range (+30 C to+250 C) This is a temperature sensitive device, which is intended to keep a temperature below one particular value during normal operating conditions, automatically switching off the electrical circuit. This device is not self-resetting and operates with manual reset option. It prevents overheating in variety of consumer, industrial and commercial products. This temperature limiter is available only with contacts that open as the temperature increases. The contacts may be reset by manually pushing on the reset button after the device has cooled below the open temperature calibration. Besides its variety of standard configurations this limiter can also be customized to the specific technical needs of the customer, assuring maximum design flexibility and usage in broad range of temperature control applications. Disc Temperature Limiter
o Tolerance of temperature limiter operating temperature, %, but not less than C Parameter Parameter Value Value ~ 2 5 0 ~ 2 5 0 16 16 10 10 10 000 10 000 3 3 50 50 1500 1500 30 to 170 170 to 250 Rated voltage, V, not more Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,6, not more Rated current, A, at power coeff. 0,6, not more Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Electric strength of insulation, V, not less than Electric strength of insulation, V, not less than Heating speed, K/min Heating speed, K/min minimum-0,1; maximum-1,0 minimum-0,1; maximum-1,0 Degrees of protection provided by enclosure Degrees of protection provided by enclosure IP4X; I P64 I P64 IP4X; 0,01; 0,05 0,05 Contact operating time, ms, not more Contact operating time, ms, not more Tolerance of operating temperature, % о Operating temperature, С о Operating temperature, С _ BASIC TECHNICAL DATA FOR TK32 (30 C 170 C) _ BASIC TECHNICAL DATA FOR TK32 (170 C 250 C)
25 14.5 4.8 0.8 14.5 11.7 3.2 9.9 0.5 14.5 4.5 3.2 4 4 0.5 26.3 3 14.5 5 0.5 3 14.5 5 5 0.5 30 1.6 14.5 6.3 7.5 0.8 35 27 1.6 14.5 6.3 0.8 14.5 14 0.8 6.3 10.7 T 03 T 05 T 07 T 09 T 11 T 13 T 04 T 02 T 01 T 06 T 08 T 10 T 12 T 14 14.5 8.5 Wire standard length: 150 mm 14.5 14 0.8 9 31 1.6 14.5 4.8 4.8 4.8 0.8 23 14.5 0.8 2.1 Table 1.1 (TERMINALS) 14.5 Wire information to be specified on the order form (type; cross-section; lengths; stripping) 14.5 8.5 0.5 3 1.5 2 2.7 Soldering balls
MG 00 MG 02 MG 04 MG 06 MG 08 MG 01 MG 03 MG 05 MG 07 NO MOUNTING CAP-FLANGE CLIP WITH ONE FIXING HOLE SCREW CAP ROUND SCREW CAP HEXAHEDRAL 16 ROTATION OR FIXED CLIP ROTATION CLIP TUBE MOUNTING SCREW CAP HEXAHEDRAL 17 Screw parameters (MX, L) to be specified on the order form Screw parameters (MX, L) to be specified on the order form Screw parameters (MX, L) to be specified on the order form Table 1.2 (MOUNTING) 14.5 15.8 0.5 23.8 18.2 0.1 0.2 3.8 30.4 0.2 14.5 23.8±0.1 20.4 5 15.8 30.4 14.5 35.5 0.1 3.8 42.25 0.2 14.5 0.5 14.5 13 15.8 0.4 25.2 8 4.02 1.9 3.8 18.2 4 16 MX 17 L 16 MX L MX L 14.5 14.5 23 14.5 3.8 Tube diameter: 14-20 mm
B1C B1CR B2P B2PR B2C B2CR B3C B3CR B4S B1P B1PR PLASTIC BODY Table 1.3 (BODY and/or CASE) PLASTIC BODY CERAMIC BODY CERAMIC BODY CERAMIC BODY T K32 1 1 2 3 4 5 4 2 5 3 MGX** *** T X* BXX PART ORDERING SYSTEM Temperature limiter model Only with cables Protection degree IP64 Mounting version (select from Table 1.2) Terminals version (select from Table 1.1) Body version (select from Table 1.3) + Operating temperature value in C and tolerance in - %*** *For wire terminals, lead wire parameters must be specified when placing an order: insulation type, cross-section area; ends type; lenght; etc. Example: TK32-T01-MG04-B2C-60±3% **For screw cap mountings, screw parameters must be specified when placing an order. ***Tolerance in % or C, whichever numerical value is bigger. 14.5 10.2 14.5 7.2 5 14.5 7.2 5 14.5 10.2 5 5 20 16 20 16 23 16 23 16 23 16 35 20 2 15 14.5 14 14.5 6.2 10.7 19.5
Contact Type: Normally Closed (One Shot) T K32OS Operating Temperature Range (+30 C to+250 C) This is a temperature sensitive device, which is intended to keep a temperature below one particular value during normal operating conditions, automatically switching off the electrical circuit. This device is operating with one-shot action and has no reset option. This temperature limiter is available only with contacts that open as the temperature increases. With variety of standard and custom configurations it provides reliable one-shot over-temperature protection and meets the specific technical needs of our customers, assuring maximum design flexibility. It is used in broad range of domestic, industrial and commercial applications. Disc Temperature Limiter
o Tolerance of operating temperature, %, but not less C Temperature of self-reset Parameter Value ~ 2 5 0 16 10 1 3 50 1500 30 to 250 Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,6, not more Number of cycles, at rated current 16 А and power coeff. 0,95, Electric strength of insulation, V, not less than Heating speed, K/min minimum-0,1; maximum-1,0 Degrees of protection provided by enclosure IP4X; IP64 Contact operating time, ms, not more о Operating temperature, С BASIC TECHNICAL DATA T K32OS 1 1 2 3 4 5 4 2 5 3 MGX** T X* *** BXX PART ORDERING SYSTEM Thermostat model Mounting version (select from Table 1.2) Terminal version (select from Table 1.1) Body version (select from Table 1.3) + Operating temperature value in C and tolerance in - %*** *For wire terminals, lead wire parameters must be specified when placing an order: insulation type, cross-section area; ends type; lenght; etc. **For screw cap mountings, screw parameters must be specified when placing an order. ***Tolerance in % or C, whichever numerical value is bigger.
25 14.5 4.8 0.8 14.5 11.7 3.2 9.9 0.5 14.5 4.5 3.2 4 4 0.5 26.3 3 14.5 5 0.5 3 14.5 5 5 0.5 30 1.6 14.5 6.3 7.5 0.8 35 1.6 14.5 6.3 0.8 14.5 14 0.8 6.3 10.7 T 03 T 05 T 07 T 09 T 11 T 13 T 04 T 02 T 01 T 06 T 08 T 10 T 12 T 14 14.5 8.5 The only option for TK24 (-45-+10) Wire standard length: 150 mm 14.5 14 0.8 9 31 1.6 14.5 0.8 4.8 4.8 4.8 23 14.5 0.8 2.1 Table 1.1 (TERMINALS) 14.5 Wire information to be specified on the order form (type; cross-section; lengths; stripping) Soldering balls 14.5 8.5 0.5 3 1.5 2 2.7
MG 00 MG 02 MG 04 MG 06 MG 08 MG 01 MG 03 MG 05 MG 07 NO MOUNTING CAP-FLANGE SCREW CAP HEXAHEDRAL 16 ROTATION OR FIXED CLIP ROTATION CLIP TUBE MOUNTING SCREW CAP HEXAHEDRAL 17 Screw parameters (MX, L) to be specified on the order form Screw parameters (MX, L) to be specified on the order form Screw parameters (MX, L) to be specified on the order form Table 1.2 (MOUNTING) 14.5 15.8 0.5 23.8 18.2 16.5 0.1 0.2 3.8 30.4 0.2 14.5 23.8±0.1 20.4 5 15.8 30.4 14.5 35.5 0.1 3.8 42.25 0.2 14.5 0.5 14.5 13 15.8 0.4 25.2 8 4.02 1.9 3.8 18.2 4 16 MX 17 L 16 MX L MX L 14.5 14.5 23 14.5 Tube diameter: 14-20 mm 3.8
B1C B2P B2C B3C B1P Only with lead wires Protection degree IP64 Only with lead wires Protection degree IP64 Only with cables Protection degree IP64 Only with lead wires and screw caps Protection degree IP64 Only with lead wires and screw caps Protection degree IP64 PLASTIC BODY WITH GROUNDING PLASTIC BODY PLASTIC BODY PLASTIC BODY SILICONE CASING Table 1.3 (BODY and/or CASE) CERAMIC BODY CERAMIC BODY CERAMIC BODY CERAMIC BODY 14.5 10.2 14.5 10.2 14.5 7.2 14.5 7.2 B4P B4C B5P B6S B3S STEEL CASING 18 12 18 15 20 15 11.5 MG 09 MG 10 SCREW CAP HEXAHEDRAL 19 Table 1.2 (MOUNTING) 4.8 0.5 20 20 40 10 8 3.7 L 19 3 MX 14.5 14 5 10.7 12.3 6.2 35 20 15 Screw parameters (MX, L) to be specified on the order form 19.5
adjustable thermostats This is a cyclic operation temperature sensitive device, which is intended to keep temperature between two particular values under normal operating conditions, automatically switching on or off the electrical circuit. Once the temperature of the bimetal plate has returned to the specified reset temperature, the contacts will automatically return to their original state. Operating temperature of this thermostat is adjusted by rotating the shaft. This thermostat can be built to either open or close its electrical contacts as the temperature increases. The current sensitive model of this thermostat is also available. In this case it is also a regulator of energy. These thermostats are widely used throughout the heating and cooling appliance industry and are designed for smooth regulation of temperature for variety of heating and cooling devices. Contact Type: Normally Closed; Normally Open T KP (Operating Temperature Range -45°C to+250°C)
CONTACT TRANSIENT RESISTANCE, mOhm CONTACT TYPE T KP 1 4 2 5 3 X MGX X PART ORDERING SYSTEM 1 2 3 4 5 Table 1.1 (CONTACT TYPE AND CONTACT TRANSIENT RESISTANCE VALUE) Normally closed (NC) Thermostat type: TKP-1; TKP-2; TKP-3; TKP CS (Current Sensitive) Mounting: A - with one mounting hole; B- with three mounting holes (Both mounting versions are applicable to all types) Rated current, A Contact type and contact transient resistance value (select from Table 1.1) 1 2 3 4 Normally closed (NC) Normally open (NO) Normally open (NO) CODE Operating temperature range in C Parameter Parameter Value Value ~ 2 5 0 ~ 2 5 0 16; 10 16; 10 2,6; 1,6 2,6; 1,6 50 50 100 000 100 000 3; 20; 5; 8; 10 10 min. 60; max. 225* -25 - +250** 5; 8; 10; 15 15 Rated voltage, V, not more Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,6, not more Rated current, A, at power coeff. 0,6, not more Number of automatic cycles, at rated current 16 (2,6) A and power coeff. 0,95, not less than Number of automatic cycles, at rated current 16 (2,6) А and power coeff. 0,95, not less than Electric strength of insulation, V, not less than Electric strength of insulation, V, not less than Heating speed, K/min *Operating temperature range can be customized according to customers’ needs **Operating temperature range can be customized according to customers’ needs Heating speed, K/min 0,01; 0,05 0,15 1500 1500 1,0 1,0 Turning range Turning range Low value High value o Reset temperature, lower than operating temperature, on C o Tolerance of operating temperature, on C o Tolerance of operating temperature, on C o Reset temperature, lower than operating temperature, on C о Control ranges, С о Operating temperature, ranges, С о ; 306 о ; 306 270 о 270 о BASIC TECHNICAL DATA SPECIFIC FOR TKP-1; TKP-2; TKP-3 BASIC TECHNICAL DATA SPECIFIC FOR TKP (Current Sensitive) X - X
Note: For all types terminal and knob configurations can be customized according to customers’ needs -45°C to + 120°C (with plastic knob) -45°C to + 250°C (with brass knob) -45°C to + 120°C (with plastic knob) TKP-1 TKP-3 Mounting MGA MGB TKP-2 TKP(CS) 4.3 ~22 ~18.5 18 51.5 12 0.5 12 6 4.3 ~22 ~16 6.3 12 ~22 ~16 18 36.5 180 105 75 0 90 Terminal configuration 26 12 32 4.6 6.3 M4 6 6 4.6-0.1 3.3 45 ~16 11.7 10 5 12 18 32.5 4 12 6.5 21 M4( 3.3) 1.5 12 6.5 8 26 32 18 32.5 12 0.5 18 4.3 18 4.6-0.1 1.5
TK124 Thermostat Operating Temperature Range (+30°C to +190°C) Contact Type: Normally Closed
23.8 19.6 9.7 9.7 0.8 21.1 40 20 30 30 6.3 10.9 10.9 1.2 1.2 0.8 3.2 3.2 4.3 4.3 Changeable size Changeable size 23.8 6.3 Parameter Value Nominal voltage, V, not more Nominal current, A, at power coeff. 0.95, not more Electric strength of insulation, V, not less than Degrees of protection provided by enclosure Heating speed, K/min Contact resistance, Ω not more Response temperature range, °C Response temperature tolerance, %, but not less than °C Switching cycles, at nominal current 10A and power coeff. 0.95, not less than BASIC TECHNICAL DATA FOR TK124 Switching cycles, at nominal current 16A and power coeff. 0.95, not less than Nominal current, A, at power coeff. 0.95, not more Reset temperature, lower than response temperature on, °C, not less than Insulation resistance, MΩ, not less than 16 10 0.05 50 1500 100 000 IP4X min-0.1; max-1.0 ~250 30 000 30 up to 190 ±3 20 (for response temperature 30-130°C) 35 (for response temperature 131-190°C)
TK127 Ø 12.7mm. Thermostat Operating Temperature Range (+30°C to +200°C) Contact Type: Normally Closed; Normally Open
3 0.5 2 4 7.5 11.5 12.7 12.7 Parameter Value Nominal voltage, V, not more Nominal current, A, at power coeff. 0.95, not more Nominal current, A, at power coeff. 0.95, not more Electric strength of insulation, V, not less than Degrees of protection provided by enclosure Heating speed, K/min Contact resistance, Ω not more Response temperature range, °C Response temperature tolerance, %, but not less than °C Switching cycles, at nominal current 5A and power coeff. 0.95, not less than BASIC TECHNICAL DATA FOR TK127 Switching cycles, at nominal current 10A and power coeff. 0.95, not less than Nominal current, A, at power coeff. 0.95, not more Reset temperature, lower than response temperature on, °C, not less than Insulation resistance, MΩ, not less than 13.5 10 5 0.05 50 1500 100 000 IP4X min-0.1; max-1.0 ~250 30 000 10 000 30 up to 200 ±3 20
Operating Temperature Range(-40°C to +170°C)
-40 to +170 41 41 15 15 15 15 20.5 31.5 37.5 29.4 15 15 15 22 22 22 22 22 22 22 20.5 22
22 23.6 23.6 23.6
This thermostat comes in 3 variations: automatic operation, manual reset and with resistance based internal heater. This thermostat can be used in high current applications (up to 45A). This thermostat can be built to either open or close its electrical contacts as the temperature increases. Once the temperature of the bimetal disc has returned to the specified reset temperature, the contacts will automatically return to their original state. Besides its variety of standard configurations the thermostat can also be customized to the specific technical needs of the customer, assuring maximum design flexibility and usage in broad range of temperature control applications for consumer, industrial and commercial products. T K34 Operating Temperature Range (-25 C to +190 C) Contact Type: Normally Closed; Normally Open 3/4”Disc Thermostat
Parameter Value ~ 2 5 0 16 25 100 000 3 50 1500 100 000 (-18) to 112 Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Maximum current, A, at power coeff. 0,95, not more Number of automatic cycles, at rated current 25 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Electric strength of insulation, V, not less than Heating speed, K/min minimum-0,1; maximum-1,0 Degrees of protection provided by enclosure IP4X 0,05 Contact operating time, ms, not more Tolerance of operating temperature, %, but not less than °C Reset temperature, lower than operating temperature on, °C not less than о Operating temperature, С BASIC TECHNICAL DATA FOR TK34 (with internal heater) (-25°C - 120°C) ±3; ±5 10 Value Maximum Calibration Resistance Voltage Internal heater Temperature Depression Open Close 120VAC 120VAC 120VAC 24VAC 7000 Ohms 9000 Ohms 3600 Ohms 281 Ohms 82.2°C 111.7°C 68.3°C 77.2°C 7.2°C 5.6°C 15°C 5.0°C 6.1°C 8.3°C 6.1°C 17.8°C TEMPERATURE DEPRESSION FOR TK34 (with internal heater) Highest calibration Set Point Range (Open or Close) Nominal Differentials (temperature difference between nominal open and close set point) Open Close Close Close Close Close Open Open Open Open 5-5.8°C 8.5-10.5°C 11-16°C 16.5-21.5°C 22-33°C (-18)°-(+26)°C (+28)°-(+111.7)°C ±3 ±3.5 ±3 ±3 ±3 ±4 ±3 ±4 ±3 ±3 ±3 ±3 ±3 ±3 ±3 ±4 ±3 ±4 ±3.5 ±3.5 CALIBRATION TEMPERATURES, DIFFERENTIALS AND STANDARD TOLERANCES OF THE TK34 (with internal heater)
Table 1.4 (CONTACT TYPE AND CONTACT TRANSIENT RESISTANCE VALUE) Normally closed (NC) 1 2 Normally open (NO) CONTACT TRANSIENT RESISTANCE, mOhm CONTACT TYPE CODE Parameter Value ~ 2 5 0 16 45 100 000 3 50 1500 100 000 (-25) to 120 Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Maximum current, A, at power coeff. 0,95, not more Number of automatic cycles, at rated current 25 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Electric strength of insulation, V, not less than Heating speed, K/min minimum-0,1; maximum-1,0 Degrees of protection provided by enclosure IP4X 0,05 Contact operating time, ms, not more Tolerance of operating temperature, %, but not less than °C Reset temperature, lower than operating temperature on, °C not less than о Operating temperature, С BASIC TECHNICAL DATA FOR TK34 (Automatic) (-25°C - 120°C) ±3; ±5 10 Number of automatic cycles, at rated current 45 А and power coeff. 0,95, not less than 6 000 Parameter Value ~ 2 5 0 16 40 1 000 3 50 1500 500 50 to 120 Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Maximum current, A, at power coeff. 0,95, not more Number of automatic cycles, at rated current 25 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Electric strength of insulation, V, not less than Heating speed, K/min minimum-0,1; maximum-1,0 Degrees of protection provided by enclosure IP4X 0,05 Contact operating time, ms, not more Tolerance of operating temperature, %, but not less than °C о Operating temperature, С BASIC TECHNICAL DATA FOR TK34 (Manual Reset) (50°C - 120°C) ±3; ±5 Number of automatic cycles, at rated current 40 А and power coeff. 0,95, not less than 500
T 01 Table 1.1 (TERMINALS) 0.8 Ø22.5 42 Table 1.2 (MOUNTING) MG 01 Ø24.7 11 4.5 R2.25 39 43 10 Ø23.8 Ø20 MG 02 Ø20 Ø23.8 10 4.25 33 5.9 4.3 R2.15 1.6 39.8 43 50 9 T 02 SELF-RESET TERMINALS R11.25 13.5 8 6.3 0.8 Ø22.5 9 R11.25 13.5 6.3 4.8 6.3 8 42 0.5 Table 1.3 (CAPS) C1P C2P C3P MANUAL RESET CAP INTERNAL HEATER CAP 10.2 5 Ø22.5 24 13.5 3 10.2 5 Ø22.5 13.5 3 24 6.6 Ø6 Ø2.8 10.2 Ø22.5 24 13.5 3 5 12.6 1 6.5 M3 The B3P package also includes 2 brass terminals for the connector, the size of which is 4.8x0.5 millimeters Ø3.2
T K34 1 1 2 3 4 5 6 7 4 2 5 3 6 7 MGX** T X* CXP X *** *** PART ORDERING SYSTEM Thermostat model Mounting version (select from Table 1.2) Terminals version (select from Table 1.1) Cap version (select from Table 1.3) + Operating temperature value in C and tolerance in - %*** + Reset temperature value in C and tolerance in - %*** Contact type and contact transient resistance value (select from Table 1.4) *Tolerance in % or °C, whichever numerical value is bigger. Example: TK34-T01-MG01-C1P-1-60°C±3%-35°C±5%
This is a cyclic operating temperature sensitive device, which is intended to control the temperature between two particular values under normal operating conditions, automatically switching on or off 2 poles of the electrical circuit. This thermostat can be built to either open or close its electrical contacts as the temperature increases. Once the temperature of the bimetal disc has returned to the specified reset temperature, the contacts will automatically return to their original state. Besides its variety of standard configurations the thermostat can also be customized to the specific technical needs of the customer, assuring maximum design flexibility and usage in broad range of temperature control applications for consumer, industrial and commercial products. T K224 Operating Temperature Range (-25 C to +190 C) Contact Type: Normally Closed; Normally Open 2 Pole
*May differ depending on the wire type and length Parameter Value ~ 2 5 0 16 10 30 000 3 50 1500 100 000 (-25) to 190 Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Rated current, A, at power coeff. 0,6, not more Number of automatic cycles, at rated current 10 А and power coeff. 0,95, not less than Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Electric strength of insulation, V, not less than Heating speed, K/min minimum-0,1; maximum-1,0 Degrees of protection provided by enclosure IP4X; IP64 0,05 Contact operating time, ms, not more Tolerance of operating temperature, %, but not less than °C Reset temperature, lower than operating temperature on, °C not less than о Operating temperature, С BASIC TECHNICAL DATA FOR TK224 (-25°C - 190°C) ±3; ±5 20
T 03 T 05 T 11 T 04 T 02 T 01 T 06 T 08 T 10 T 12 wire standard length: 150 mm Table 1.1 (TERMINALS) wire information to be specified on the order form (type; cross-section; lengths; stripping) soldering balls 6.3 0.8 Ø22 69° 111° 6.3 Ø22 0.8 69° 111° 6.3 Ø22 23 23 5 0.5 Ø22 23 69° 111° 69° 111° 0.8 23 Ø22 69° 111° 23 3.2 0.6 5 7.5 10.7 4 Ø22 Ø22 69° 111° 5 Ø3 23 0.5 69° 111° 4.8 23 Ø22 69° 111° 4.8 23 4.8 Ø22 Ø2.1 0.8 0.8 0.8 Ø22 69° 111° 23 9 Ø22 Ø22 23 69° 111° 69° 111° 23 15.5 23 69° 111° 5 T 14 T 13
MG 00 MG 01 NO MOUNTING ROTATION OR FIXED CLIP Table 1.2 (MOUNTING) 23 69° 111° 4.8 6.4 0.8 Ø22 Ø22 4.8 6.4 0.8 69° 111° 23 9 T 19 T 18 Table 1.1 (TERMINALS) Ø23.8 Ø22 MG 07 24 MG 08 SCREW CAP SW 24
BS BP Only with lead wires Protection degree IP64 PLASTIC BODY Table 1.3 (BODY and/or CASE) CERAMIC BODY BC STEEL CASING 9.5 Ø22 Ø23.8 16 9.5 Ø22 Table 1.4 (CONTACT TYPE AND CONTACT TRANSIENT RESISTANCE VALUE) Normally closed (NC) 1 2 Normally open (NO) CONTACT TRANSIENT RESISTANCE, mOhm CONTACT TYPE CODE T K224 1 1 2 3 4 5 6 7 4 2 5 3 6 7 MGX** T X* BXX X *** *** PART ORDERING SYSTEM Thermostat model Mounting version (select from Table 1.2) Terminals version (select from Table 1.1) Body version (select from Table 1.3) + Operating temperature value in C and tolerance in - %*** + Reset temperature value in C and tolerance in - %*** Contact type and contact transient resistance value (select from Table 1.4) *For wire terminals, lead wire parameters must be specified when placing an order: insulation type, cross-section area; ends type; lenght; etc. **Tolerance in % or °C, whichever numerical value is bigger. Example: TK224-T01-MG01-BP-1-60°C±3%-35°C±5%
T K232 Operating Temperature Range (+50 C to +190 C) 2 Pole Temperature Limiter Contact Type: Normally Closed This is a temperature sensitive device, which is intended to keep a temperature below one particular value during normal operating conditions, automatically switching off 2 poles of the electrical circuit. This device is not self-resetting and operates with manual reset option. It prevents overheating in variety of consumer, industrial and commercial products. This temperature limiter is available only with contacts that open as the temperature increases. The contacts may be reset by manually pushing on the reset button after the device has cooled below the open temperature calibration. Besides its variety of standard configurations this limiter can also be customized to the specific technical needs of the customer, assuring maximum design flexibility and usage in broad range of temperature control applications.
*May differ depending on the wire type and length o Tolerance of temperature limiter operating temperature, %, but not less than C Parameter Value ~ 2 5 0 16 10 000 3 50 1500 50 to 190 Rated voltage, V, not more Rated current, A, at power coeff. 0,95, not more Number of automatic cycles, at rated current 16 А and power coeff. 0,95, not less than Electric strength of insulation, V, not less than Heating speed, K/min minimum-0,1; maximum-1,0 Degrees of protection provided by enclosure I P64 IP4X; 0,05 Contact operating time, ms, not more о Operating temperature, С _ BASIC TECHNICAL DATA FOR TK232 (50 °C 190 °C) ±3; ±5
T 03 T 05 T 11 T 04 T 02 T 01 T 06 T 08 T 10 T 12 wire standard length: 150 mm Table 1.1 (TERMINALS) wire information to be specified on the order form (type; cross-section; lengths; stripping) soldering balls 6.3 0.8 Ø22 69° 111° 6.3 Ø22 0.8 69° 111° 6.3 Ø22 23 23 5 0.5 Ø22 23 69° 111° 69° 111° 0.8 23 Ø22 69° 111° 23 3.2 0.6 5 7.5 10.7 4 Ø22 Ø22 69° 111° 5 Ø3 23 0.5 69° 111° 4.8 23 Ø22 69° 111° 4.8 23 4.8 Ø22 Ø2.1 0.8 0.8 0.8 Ø22 69° 111° 23 9 Ø22 Ø22 23 69° 111° 69° 111° 23 15.5 23 69° 111° 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 4.8 5 T 14 T 13
MG 00 MG 01 NO MOUNTING ROTATION OR FIXED CLIP Table 1.2 (MOUNTING) 23 69° 111° 4.8 6.4 0.8 Ø22 Ø22 4.8 6.4 0.8 69° 111° 23 9 4.8 4.8 T 19 T 18 Table 1.1 (TERMINALS) Ø23.8 Ø22 MG 07 24 MG 08 SCREW CAP SW 24
BP PLASTIC BODY Table 1.3 (BODY and/or CASE) CERAMIC BODY BC 9.5 Ø22 4.8 9.5 Ø22 4.8 T K232 1 1 2 3 4 5 4 2 5 3 MGX** *** T X* BXX PART ORDERING SYSTEM Temperature limiter model Mounting version (select from Table 1.2) Terminals version (select from Table 1.1) Body version (select from Table 1.3) + Operating temperature value in C and tolerance in - %*** *For wire terminals, lead wire parameters must be specified when placing an order: insulation type, cross-section area; ends type; lenght; etc. Example: TK232-T01-MG00-BC-60°C±3% **Tolerance in % or °C, whichever numerical value is bigger.
Address: “Thermorex” SAS, 18, rue Pasquier, 75008 Paris, France tel.: +31(0) 61 55 22 880, e-mail: info@thermorex.fr, marketing@thermorex.fr Manufacturing plant: “Thermorex” CJSC, 24/41 Fuchik str., 0048, Yerevan, Armenia tel.: +37410 39 58 84, 37410 34 93 51, fax: +37410 34 98 86, e-mail: info@thermorex.org, marketing@thermorex.org
RkJQdWJsaXNoZXIy NzAwNg==